|
Domus Line 12Vdc Strip Lighting - Side Emitting High Emission
Domus Line 12Vdc Strip Lighting - Side Emitting High Emission
https://www.fit-nz.co.nz/DOMUS-Line-12Vdc-Strip-Lighting-Side-Emitting-High-Emission-250x220.jpg
SIDE-EMITTING AND SUPER FLEXIBLE Developed with an innovative diffusing silicone material extrusion technology, this LED strip from Domus Line was specifically conceived for recessed installation and tight corners. It's fantastic for creative lighting installations. NO-DOT EFFECT The SE H4 configuration comes with no-dot effect technology, for homogeneous light emission. High lighting performance, ideal for installation on the sides of wardrobes, and other applications that require integrating a minimal lighting system. NO GLUE! Neither adhesives nor glue are required for the SE H4 strip; the soft silicone profile is installed simply by pressing into a 4mm milled groove
Find Out More About Innovative SE H4 LED Strip
SE H4 12Vdc LED Strip Lighting Cut Length & Attached Power Cable
SE H4 12Vdc LED Strip Lighting Cut Length & Attached Power Cable
Designed in Italy to comply with Australian/New Zealand standards Developed with an innovative diffusing silicone material extrusion technology, this LED strip was specifically conceived for recessed installation and is ideal for use in wardrobes, pantry cupboards and many other situations. Exceeds international safety requirements for temperature generation limits for recessed application
Side emitting 'No dot technology' for homogenous, no visible dot light emission Super flexible for tight corners or creative lighting designs Recessed installation in 4mm wide / 10mm deep milled grooves 7mm diameter hole required for plug connector to exit No tape or tools required; simply press into your pre-milled groove Minimum radius of just 15mm
Standard SE H4 comes with 150mm power supply cable and 1 x 2m extension cable, all with Micro12 connectors. 'Double ended' models come with 150mm power supply cable on each end and 2 x 2m extension cables, all with Micro 12 connectors.
Maximum suggested length of 3m in a run Customisable lengths - SE H4 strip may be cut in 25mm increments Should you trim the SE H4 strip, a cap is provided for insertion into cut end SE H4 is very flexible and is suitable for tight corners, however not a 90° corner 120 LED/m LED strip only IP44 rated; protected against solid foreign objects greater than 1mm and splashes of water from any direction
Nominal power: 1m 12W 2m 22W 3m 30W Luminous Efficiency: 70lm/W
Available in Natural White and Warm White light colours Available in 1m, 2m and 3m lengths 2m and 3m lengths also available with double power cables
Extension cords available in 1m and 2m lengths to extend distance between LED driver distribution block and LED strip. Keep to a minimum and do not exceed 6m total length. Don't forget! Order LED distributor block and LED drivers separately
For 1m SEH4 strip order 15W driver per length, for 2m & 3m SEH4 strips order a 30W driver per length. If running more than 3m on one driver, order a 75W but do not exceed 6m in total. Maximum continuous run length: 6m per any one strip. Multiple lengths may be run from a distributor block providing driver capacity is sufficient. Please refer to the diagram on the image carousel for clarification regarding the direction in which Domus Line SE H4 LED strip bends. This range has been marked for deletion. Please talk to us regarding quantities if you are ordering in volume. Individual items will be removed from the website as stock sells out.
|
|
6 Reasons To Choose SE H4 LED Strip from DOMUS LINE
SE H4 can be used on curves and on relatively tight corners, with a minimum radius of just 15mm, so it's great for creative installations.
SE H4 features no dot effect technology for even light emission.
SE H4 has high lighting performance so is excellent for task lighting and cupboard internals. Warm White and Natural White options are available.
SE H4 is slimline and recess installed so looks integrated and unobtrusive.
SE H4 can be trimmed at 25mm intervals, so you can customise the length to your project. Some lengths come with double power cables so even if you divide the length, the offcut remains usable, minimising waste.
SE H4 is designed for fast and easy installation; no glue or adhesive strip required. Just press into a 4mm milled groove.
|
|
|
|